FreeQRCode3D עברית

What size should a QR code be?

Updated October 12, 2026 · 6 min read

A QR code that is too small is the number one reason people walk past it. Three things decide the right size: how far people stand, how much data the code holds and how you produce it.

The distance rule: about 1 to 10

A practical rule used in printing is that a QR code can be scanned from a distance of roughly ten times its width. A code 5 cm wide reads well from about 50 cm, and a code 20 cm wide from about 2 meters. Good light and a modern phone stretch this a little; a dark corner or a worn print shortens it.

Where it isTypical distanceCode width
Keychain or business card15–25 cm2.5–3 cm
Table stand at a restaurant or counter30–60 cm5–7 cm
Sign on a wall next to the door1–1.5 m10–15 cm
Shop window seen from the sidewalk2–3 m20–30 cm

Link length changes the size of every square

A QR code is a grid of small squares called modules. The more characters you encode, the more modules the grid needs. The smallest QR code (version 1) is 21 × 21 modules, and each version adds four modules per side. With the common medium error correction level, a version 1 code holds up to 14 characters of a link, version 3 (29 × 29) up to 42 and version 5 (37 × 37) up to 84.

For a printed object this matters a lot: if the code has to fit in 5 cm, a long link means smaller squares. That is why a short link, for example your own domain or a link shortener, gives you bigger squares and a code that scans faster.

The minimum square size for 3D printing

With a standard 0.4 mm nozzle, keep each module at least 1.5 mm wide. Smaller squares round off at the corners and neighbors start to merge. Our generator shows the module size live while you change the dimensions and warns you when it gets too small.

Example: a code with 29 modules per side at 1.5 mm per module is 43.5 mm wide, plus the quiet zone around it.

Error correction: L, M, Q and H

QR codes contain redundant data so they still work when part of the code is dirty or damaged. Level L can recover about 7% of the code, M about 15%, Q about 25% and H about 30%. Higher levels need more modules for the same link, so the squares get smaller. Medium (M) is a good default; choose a higher level if you put a logo in the middle of the code or if it will live outdoors.

Don't forget the quiet zone

The QR standard asks for an empty margin of four modules around the code. Phones use this light border to find where the code starts. On a printed stand or sign, keep the base color all around the code and avoid putting text, frames or edges right against it.

Quick checklist

Size cheat sheet by distance

Using the rule of one to ten, the minimum width of the code grows with the distance from which people will scan it:

These are minimums for good conditions. If people will scan quickly or in poor light, go a size up.

Viewing angle

A code looks distorted when it is seen from the side, and the phone has to work harder to read it. Scanning is comfortable within roughly 30 degrees of straight on and gets unreliable beyond about 45. For a table stand, a slight backwards tilt is better than a flat code lying on the table, because it faces the person at the table instead of the ceiling.

Smaller nozzles for smaller codes

With a standard 0.4 mm nozzle, squares smaller than about 1.5 mm start to blur. A 0.25 mm nozzle can print finer squares, but it prints much more slowly and clogs more easily, so it only makes sense when the code really has to be small. Whatever the nozzle, print one test piece and scan it before you commit.

Error correction and size are linked

Higher error correction lets a code survive more damage, but it adds squares, and more squares mean each one is smaller at the same overall size. For a clean 3D printed object that will not get dirty or scratched, a medium level is usually the right balance. Reserve the highest level for codes with a logo or an emoji in the middle, which cover part of the pattern.

Related guides

Make a QR code table stand